How to Remove Sand Textured Paint from a Wall

Some people find textured wall paint appealing, while others dislike it. So, whoever dislikes it, want to remove textured paint from a wall.

Don’t get relaxed if you like it, because you may also need to undergo the removal process if peeling off happens on the wall.

Removing sand textured paint from a wall is messy, but the result will put a smile on your face. So, what are the methods to remove sand textured paint from a wall? You can do this following a few methods, which are:

  • Using water and a floor scraper or drywall blade to scrape off the texture.
  • Covering up the texture up using a mixture of water and joint compound.

Let’s have a look at the step-by-step procedures of the methods as mentioned above.

How to Remove Sand Textured Paint from a Wall

Remove Sand Textured Paint from a Wall -In 3 Fixation Processes:

Consider these steps of preparing the workplace common for every process since these steps are unavoidable.

After the preparation of the workspace, we will go through the procedures.

Preparing the Workspace in 4 steps:

Step 01: Room Furniture Covering

Room Furniture Covering

As stated earlier, it is a messy job. Since you are dealing with wall paint and dust, everything in your room needs to be well-covered. Use old sheets, tarps, or old cloth to wrap up your room furniture.

  • Also, make sure to cover the vents using plastic so that air can’t enter the room. This will prevent the spreading of dust throughout the room.

Step 02: Moving Out Furniture from Room if Necessary

Are you worried about if your furniture gets damaged? If so, you should move out your furniture from your room. If possible, move out the delicate or vintage pieces.

Step 03: Cover the Floor using Tarps

Cover the Floor using Tarps

You can’t avoid cleanup after accomplishing the floor. Covering the floor with tarps or cloth will let you minimize the cleaning process. Use painter’s tape to cover the edges.

Step 04: Wear Safety Gears

wearing safety goggles and a face mask
face mask: Check on Amazon=>  safety goggles: Check on Amazon=>

When removing sand textured paint from a wall, wearing safety gears is mandatory. Since a lot of dust gets created in this process, protect your eyes and face from debris wearing goggles and a face mask too. If you remove lead paint, it would be best to wear a respirator mask rather than a regular face mask. A pair of gloves will be beneficial at the time of joint compound application.

  • Lead paints are generally used in old houses. Extra precautions are compulsory if you need to deal with lead paint. Cover up your furniture using 6 mm of plastic sheets and provide 2 layers of plastic.

Let’s move to the methods now.

Method 01: Peeling off the Texture

After preparing your workplace, arrange the below-required ingredients to start this method.

  • Water sprayer.
  • Floor scraper or drywall blade.
  • Sandpaper (60 to 100 grit)
  • Sponge
  • Joint compound
  • Wallboard knife

Step 01: Start Spraying Water into a Small Area

spraying water on sanding wall
Water sprayer=>

Firstly, starting with a few square feet will be a good decision. Use a water sprayer to coat the area thoroughly. Avoid starting with an enormous area because a little bit of practice is necessary before working with a large area. After spraying water, give time to the wall to absorb the water. Scraping off the texture will be much easier when you apply water onto the wall.

  • In order to understand whether the water is soaked, touch the area. If you get a bit soft feeling, be sure the water is soaked.
  • Re-spray water if it is not.

Step 02: Use the Scraper for Floor or Drywall Blade to Scrape the Wall

Drywall Blade to Scrape the Wall
Putty Knife Scraper=>

Be steady when holding the drywall blade or Paint scrapper in contrast to the wall. You can comfortably work with the scrapper if you hold it at an angle of 30°.

Step 03: Start Scrapping

Start Scrapping

However, adjust the angle according to your preference. Also, you will need to go slow and faster, depending on the response of the wall. This is the reason; you should start with an insignificant area.

Step 04: Speed Up the Process

speed up sanding with drywall sander
speed up sanding=>

Once you are familiar with the process, spray water on a larger area and continue scrapping.

  • Don’t miss out on any area. You can make a system to scrape off the wall. Make a plan on how you cover the entire room without missing any spots.
  • You can apply adequate water if needed.

Step 05: Sand Any Rough Spots

After you complete scraping off the entire room, take 60 to 100 grit sandpaper and check for any uneven spots. Sand down if you find any rough spots, which will give you a smooth surface.

drywall sanding screen
sanding screen=>
  • A sanding screen is also beneficial in this process.
  • Don’t sand down hard to avoid damage to the wall.
  • To Speedup the work, use a Best Drywall Sander

Step 06: Use a Damp Sponge to Swab Down the Wall

Use a Damp Sponge to Swab Down the Wall

Take a sponge and soak it into water. Use it to swab down the wall. This will help you to minimize dust from the area. Wiping may require during the process.

Step 07: Use a Wallboard Knife to Apply Joint Compound

Apply Joint Compound by Wallboard Knife
Wallboard Knife=>

Take a 15 cm wallboard knife and start applying a 3.2 mm joint compound throughout the wall. Don’t rework and aim to complete with one go. This will give a more even look. Give the coat a rest for 24 hours.

Step 08: Again, use a Sandpaper to Smoothen any Rough Edges

After 24 hours, use medium-grit sandpaper to smoothen rough edges.

Read More Also: How to Smooth Plaster Walls Before Painting [Fix Rough Uneven Walls]

Step 09: Provide Another Coat of Joint Compound

apply second coat drywall mud
drywall mud=>

Again provide a joint compound coat on the wall. This time, aim for a thin coat. This cot will be useful to fill up the tiny spots. And again, let it rest for the next 24 hours.

Step 10: Sand the Wall Again

Once the coat is dried, sanding is necessary for the last time using medium-grit sandpaper. You can use a vacuum cleaner to clean the area.

Step 11: Applying Primer

Applying Primer by paint roller

Don’t forget to apply a primer before painting. A paint roller will be helpful at this point. You can create your expected paint according to your choice.

Method 02: Using a Mixture of Water and Joint Compound

This method requires several coats of joint compound. As a result, it is a time-consuming and lengthy process.

Step 01: Joint Compound Mixing

Mixing Joint Compound with water
Dry Joint Compound=>

In this process, the joint compound needs to be mixed with water and give the compound a little bit thin. Don’t mix a full bucket of water at once; ensure a mixture of water and joint compound in batches.

Step 02: Apply the Compound on the Wall Using a Roller

Applying Compound on sand texture Wall
Paint Roller=>

Take a paint roller, submerge it into the water, and compound the mixture. Then start applying on the wall. Go from top to bottom. Ensure keeping the edges wet. The edged area will merge to the following section.

Step 03: Give the Joint Compound Rest to Dry

We will apply 2 coats of the joint compound. After applying the first coat, it is mandatory to give it a rest for 24 hours. Leave the coat for 24 hours to dry.

Step 04: Sand if Necessary

If you find any rough area over the wall, use a drywall sanding block with sandpaper to smooth the spot. When you do so, more dust will be created. So, use a wet sponge to wipe down the rough area before sanding. A vacuum cleaner will let you clean the dust.

Step 05: Applying 3 – 5 layers of Joint Compound According to Your Need

If you are unhappy with the joint compound result, you can apply more layers. An enough layer will assist you to hide the sand textured paint from a wall. The layers need enough time to dry before applying every layer. So, don’t forget to give it. And after drying, check, and if any rough spots have appeared, use medium-grit sandpaper to smooth out.

Step 06: Primer Applying

Finally apply a primer
exterior primer=>

Finally, apply a primer with a paint roller before painting the wall. Ensure applying primer evenly. The final output will be affected if you apply primer unevenly.

Method 03: Living with the Textured Paint

This method is tricky. You will need to distract the attention of a viewer from the textured wall. For this, follow the below tricks.

  • Hang artwork on the wall. This is a good idea to trick an eye.
  • Install low lighting in the room. Keep the focus of the light away from the wall.

Tips: If you plan to use paint removal chemicals to remove sand textured paint from a wall, don’t do this because the chemicals are harmful to use.

How do you cover sand textured walls?

Answer: Following the above-discussed processes, covering sand textured walls is possible. Every process has a few common steps: preparing the workplace, applying a joint compound, and finally using a primer before painting to cover sand textured walls. In between these steps, you may need to provide several coats of joint compound and use sandpaper as necessary to smooth out a textured wall.

Final Thought

The processes are cumbersome, but who doesn’t love to get a nicely textured wall paint? Consider following the above methods as a DIY project. Impress your family and friends by doing it efficiently. Additionally, don’t forget to wear safety gear; safety should get topmost priority all the time. Best of Luck! It’s all about How to Remove Sand Textured Paint from a Wall.

Last Updated on August 27, 2021 by Rogers Weber

[As an Amazon Associate I earn from qualifying purchases.]

One Comment

Add a Comment

Your email address will not be published. Required fields are marked *